Additional components ORTEA Bypass-10, FL170.10.00, SPD, etc.

The bypass allows you to disconnect the stabilizer from the line feeding the load. Thus, it is not necessary for technical personnel to disconnect the load to work with the internal components of the stabilizer and perform maintenance or repair operations. While the stabilizer is in bypass mode, the load is powered directly from the mains. Accordingly, the voltage is not stabilized at the same time.

Models: Bypass-10, Bypass-16, Bypass-20, Bypass-25, Bypass-32, Bypass-40, Bypass-50, Bypass-63, Bypass-80, Bypass-100, Bypass-125, Bypass-160, Bypass-200, Bypass-250, Bypass-320, Bypass-400, Bypass-500, Bypass-630, Bypass-800, Bypass-1000, Bypass-1250, Bypass-1600, Bypass-2000, Bypass-2500, Bypass-3200, Bypass-4000, Bypass-5000, Bypass-6300, Bypass-R-125, Bypass-R-160, Bypass-R-200, Bypass-R-250, Bypass-R-320, Bypass-R-400, Bypass-R-500, Bypass-R-630, Bypass-R-800, Bypass-R-1000, Bypass-R-1250, Bypass-R-1600, Bypass-R-2000, Bypass-R-2500, etc.

EMI/RFI filters. The additional installation of EMI/RFI filters is the optimal solution for eliminating electromagnetic interference generated by many electronic devices.

Models: FL170.10, FL170.1000.00, FL170.120.00, FL170.150.00, FL170.1600.00, FL170.250.00, FL170.2500.00, FL170.30.00, FL170.300.00, FL170.400.00, FL170.50.00, FL170.500.00, FL170.700.00, FL170.80.00, FL170.800.00, etc.

Circuit breakers can be installed in each voltage stabilizer. The automatic switch on the input will protect the stabilizer from possible short circuits, and the automatic switch on the output from possible overloads.

Protection against high and low voltage provides double protection: it delays the connection of the load to the stabilizer for a while at each start, which ensures that the stabilized voltage is supplied to the consumer's equipment and protects the load from surges and voltage drawdowns and overloads, disconnecting it from the stabilizer. The protection is triggered when the output voltage exceeds the specified range (relative to the nominal value). When the power is restored to normal, the load is automatically connected again.

Full protection system + bypass. The complete protection package includes an input circuit breaker (QF1), a bypass line based on an automatic circuit breaker with a locking function (QF2), an automatic motorized output circuit breaker (QF3). An input circuit breaker protects the device from possible failures and/or short circuits inside the stabilizer. The circuit breaker protects the load from overloads and short circuits in bypass mode. An automatic motorized output switch with a locking function provides protection against overloads, short circuits, over/under voltage, phase alternation errors and phase breakage.

The isolating transformer at the input of the stabilizer is the best solution for galvanic isolation between the stabilizer and the power grid, for connection according to the "triangle-star" or "triangle-zigzag" scheme, which provides suppression of third and multiples of three harmonics and equalization of the balance between voltages in different phases, the formation of a fixed and stable zero point, for protection against overvoltage, provoked by connections/disconnections of equipment on the line.

The built-in reactive power compensation device (UKRM) can be placed in the same housing with a stabilizer, which allows you to combine the functions of voltage stabilization and correction of the power factor of the equipment in one device.

Surge protection Devices (SPD) protect the load and stabilizer from voltage surges caused by atmospheric phenomena or the operation of other equipment, discharging high-voltage discharges to the ground.

A symmetrical transformer forms a reference neutral point in the system and is used in cases when there is no neutral wire in the AC network or when a stable neutral is required to supply the load.

Degree of protection IP54/55 for indoor and outdoor installation. All voltage stabilizers ORTEA can be mounted inside cabinets with a degree of protection IP54 or IP55, equipped with an air conditioning system or fans with special filters to ensure effective cooling of components. The housing is completely sealed, which makes the stabilizer suitable for use in humid and dusty environments.